ABSTRACT
Objectives: To determine the fluorescence property of Vitapan 3D-Master shade guide tabs with a spectrophotometer. Materials and Methods: Fluorescence property of 29 shade tabs, in both of original and ground-to-flat forms, was determined by a reflection spectrophotometer. Color difference (ΔE*ab-FL) by the inclusion and exclusion of the UV component of a standard daylight simulator (CIE standard illuminant D65) was calculated to determine the fluorescence color change. Fluorescence peak was expressed as the difference in spectral reflectance values by the UV component. Results and Conclusion: ΔE *ab-FL values were in the range of 0.2 to 2.7 (mean: 1.2±0.6) for the original and 0.5 to 1.6 (mean: 0.9±0.1) for the ground-to-flat tabs, which was significantly different based on paired t-test (p<0.05); however, fluorescence peak was not detected in all the shade tabs. Therefore, fluorescence property of Vitapan 3D-Master shade guide should be modified to have similarfluorescence property of natural teeth and corresponding restorative materials.
ABSTRACT
Indirect resin composites are generally regarded to have better color stability than direct resin composites since they possess higher conversion degree. OBJECTIVE: The present study aimed at comparing the changes in color (ΔE) and color coordinates (ΔL, Δa and Δb) of one direct (Estelite Sigma: 16 shades) and 2 indirect resin composites (BelleGlass NG: 16 shades; Sinfony: 26 shades) after thermocycling. MATERIAL AND METHODS: Resins were packed into a mold and light cured; post-curing was performed on indirect resins. Changes in color and color coordinates of 1-mm-thick specimens were determined after 5,000 cycles of thermocycling on a spectrophotometer. RESULTS: ΔE values were in the range of 0.3 to 1.2 units for direct resins, and 0.3 to 1.5 units for indirect resins, which were clinically acceptable (ΔE<3.3). Based on t-test, ΔE values were not signifcantly different by the type of resins (p>0.05), while ΔL, Δa and Δb values were signifcantly different by the type of resins (p<0.05). For indirect resins, ΔE values were infuenced by the brand, shade group and shade designation based on three-way ANOVA (p<0.05). CONCLUSION: Direct and indirect resin composites showed similar color stability after 5,000 cycles of thermocycling; however, their changes in the color coordinates were different.
Subject(s)
Color , Composite Resins/chemistry , Methacrylates/chemistry , Analysis of Variance , Hot Temperature , Materials Testing , Spectrophotometry , Time FactorsABSTRACT
The purpose of this study was to determine the influence of incrementally added uncured HEMA in experimental HEMA-added glass ionomer cement (HAGICs) on the mechanical and shear bond strength (SBS) of these materials. Increasing contents of uncured HEMA (10-50 wt. percent) were added to a commercial glass ionomer cement liquid (Fuji II, GC, Japan), and the compressive and diametral tensile strengths of the resulting HAGICs were measured. The SBS to non-precious alloy, precious alloy, enamel and dentin was also determined after these surfaces were subjected to either airborne-particle abrasion (Aa) or SiC abrasive paper grinding (Sp). Both strength properties of the HAGICs first increased and then decreased as the HEMA content increased, with a maximum value obtained when the HEMA content was 20 percent for the compressive strength and 40 percent for the tensile strength. The SBS was influenced by the HEMA content, the surface treatment, and the type of bonding surface (p<0.05). These results suggest that addition of an appropriate amount of HEMA to glass ionomer cement would increase diametral tensile strength as well as bond strength to alloys and teeth. These results also confirm that the optimal HEMA content ranged from 20 to 40 percent within the limitations of this experimental condition.